English
Chinese (Traditional)
French
German
Korean
Russian
Spanish
Turkish
DBL220 Series
● It can be connected to the speed display to monitor the speed; It can also be connected to the handheld intelligent setting unit to set the driver parameters
● Double closed-loop design of current speed with large torque at low speed and stable operation
● High torque and high speed output, the maximum speed reaches 10000rpm
● The method of controlling the speed: via PWM or potentiometer
● There are EN (enable), DIR (direction), X1 (brake) signal control pins
● Can output speed measuring pulse wave FG (photoelectric isolation, gate output)
● Can output alarm signal, ALM for user detection (photoelectric isolation, gate output)
● With over-current, over-voltage, under-voltage, fan control, Hall sensor phase error, rotor-blocked and other
▍Electrical Performance
| Power Input | AC80V ~ 220V AC power input (capacity is selected according to motor power) | |
| Rated Current | Not more than 5A (depending on the equipped motor and rated load) | |
| Rated Power | ≦1100W | |
| Suitable Motor | Suitable for Motor with output power ≦750W | |
| Insulation Resistance | At normal temperature > 500MΩ | |
| Dielectric Strength | 0.5KV at normal temperature and pressure for 1 minute | |
| Cooling Method | Natural air cooling & forced-air cooling | |
|
Environments
|
Occasion | Try to avoid dust, oil mist and corrosive gas |
| Temperature | 0℃ ~ +50℃ | |
| Humidity | <80%RH (no condensation, no frost) | |
| Vibration | <0.5G (4.9m/s2) 10Hz-60Hz (non-continuous operation) | |
| Storage Temperature | -20℃ ~ +65℃ | |
| Dimensions | 150mmX97.5mmX53mm | |
| Weight | Around 0.55Kg | |
● At ambient temperature Tj= 25 ℃
▍Electric Connection
| Type | Terminal Symbol | Description |
| RS232 | TTL | It can be connected to the speed display to monitor the speed; it can also be connected to the handheld setting unit to set the driver parameters. For details, please refer to the instructions of the handheld setting unit. |
|
Control Signal Connections
|
+5V1 | Control signal power supply is positive (built-in power output) |
| VSP | External speed control signal control method: 1. The speed can be adjusted by changing the voltage of the VSP terminal through an external potentiometer, ranging from 0.4 to 4.8V 2. The speed can be adjusted by changing the duty cycle of external PWM with frequency greater than 50Hz, the range is 15% ~ 96% |
|
| X1 | Brake signal input, low potential brake, and the red light of the brake status will be always off (brake braking force can be adjusted separately according to user requirements) | |
| FG | Motor speed pulse output can be converted to the actual motor speed by measuring the frequency of this signal | |
| DIR | The high and low potentials control the motor forward and reverse. – connect the GND1 motor to reverse (counterclockwise) – not connect the GND1 motor to forward (clockwise) |
|
| EN | Motor enables control. – EN connects to GND1, the motor turns (connected state) – EN does not connect, the motor does not turn (offline state, the red light in this state is always on) |
|
| ALM | Alarm output. While in alarm state and outputting low potential, the indicator light is always on | |
| GND1 | Control signal power ground | |
|
Hall Signal Terminal
|
+5V2 | Motor Hall power supply +5V |
| HU | Hall sensor signal U-phase input | |
| HV | Hall sensor signal V-phase input | |
| HW | Hall sensor signal W-phase input | |
| GND2 | Motor Hall Power 0V | |
|
Motor and Power Supply Terminal
|
U、V、W | Connect to the motor three-phase winding |
| AC1、AC2 | AC80V ~ 250V Power supply input (panel label: AC80V ~ 220V) |
▍Dimension
